Aliphatic Research Articles

Sequential oxidation-composting-phytoremediation treatment for the management of an oily sludge from petroleum refinery

Oily sludges are generated in large quantities in petroleum refinery wastewater treatment plants. Given their complex composition, they are classified as hazardous waste. Selecting a single treatment technique for their remediation is challenging.This work aims to assess the extent of composting followed by phytoremediation on an oily sludge from an API separator unit, pre-treated by chemical oxidation with alkaline activated persulfate (PS). 18% of total petroleum hydrocarbons (TPH) were determined by IR spectroscopy. The aliphatic hydrocarbon content was 4714 ± 250 ppm by GC-FID, and aromatics were not detectable, suggesting a high amount of non-chromatographable complex hydrocarbons. The density of generalist and hydrocarbon-degrading populations of the oily sludge estimated by quantitative polymerase chain reaction (qPCR) evidenced an autochthonous microbiota with hydrocarbon-degrading capacity. The oxidative treatment with PS removed 31% of the TPH determined by IR after 20 days. The significant reduction of the native bacterial community was counterbalanced by coupling a composting treatment. Co-composting the sludge with goat manure and oat straw produced, after a year, a 96% reduction in TPH content, regardless of the oxidative pretreatment. Organic matter transformation was evidenced by the decrease of dissolved organic carbon (DOC) and the variation in E4/E6 ratio. The matrices obtained of composting were used as substrates for phytoremediation for 4 months. Ryegrass seeds were planted in both PS-treated and untreated sludge substrates. The presence of the plant grown in the pre-oxidised and composted substrate resulted in a higher aerial biomass of ryegrass (67%), an increase in enzymatic activities, and higher concentration of DOC, although without evidence of additional dissipation of TPH.The dynamics of the bacterial communities of the different substrates generated during the biological treatment were analyzed by Illumina NovaSeq DNA sequencing of 16S rRNA amplicons. The findings mirrored a succession compatible with that described in contaminated matrices, but also in other non-contaminated ones.According to these findings, an organic matter transformation process occurred, which included the complex hydrocarbons of the oily sludge, resulting in an active substrate that promoted the retention of nutrients and water and provided the necessary support for plant development.

Tracking the Dimensionality Transition from a Three Dimensional Single Crystal to a Two Dimensional Perovskite

AbstractThis work carefully studied the transition from 3D perovskite to 2D perovskite. Our system includes single crystals (SCs) of MAPbBr3, which were dipped in a solution of barrier molecules. Three monoammonium cations and one di‐ammonium cation were studied. Absorbance and cathodoluminescence were used to follow the formation of low‐dimensional perovskite on the SC surface. Quantitative nuclear magnetic resonance and scanning electron microscopy assist in quantitatively tracking the exchange process. We followed the barrier molecules′ concentration during the exchange process and their penetration depth into the 3D single crystal. The short aliphatic chain penetrates much farther into the crystal (ca. 450 μm) than the long aliphatic chain barrier molecule. In contrast, the process time is the opposite: the long aliphatic chain requires 5 days to achieve an equilibrium state compared with 15 days for the short aliphatic chain. Ab initio calculations indicate that the exchange process initiates due to the methylammonium vacancies on the surface, and the process is inhibited by the interactions between the −NH3 group and the PbBr2 planes. This work sheds light on the kinetics and thermodynamics of the transition from 3D to 2D perovskites, which is important for stabilizing the hybrid perovskites.

ATI stabilized germylene cation as a cyanosilylation catalyst for aldehydes and ketones.

The aminotroponiminate (ATI) ligand stabilized germylene cation [(i-Bu)2ATIGe][B(C6F5)4] (2) is found to be an efficient low-valent main-group catalyst for the cyanosilylation of aldehydes and ketones (ATI = aminotroponiminate). It was synthesized by reacting [(i-Bu)2ATIGeCl] (1) with Na[B(C6F5)4]. The catalytic cyanosilylation of diverse aliphatic and aromatic carbonyl compounds (aldehydes and ketones) using 0.075-0.75 mol% of compound 2 was completed within 5-45 min. The catalytic efficiency seen with aliphatic aldehydes was around 15,800 h-1, making compound 2 a capable low-valent main-group catalyst for the aldehyde and ketone cyanosilylation reactions.

Nano Encapsulation of An Essential Oil Transpire the Therapeutic Approach.

Essential oils are natural compounds extracted from plants that are volatile and sensitive to heat. Due to their therapeutic value, essential oils are now used in many industries, including the sanitary, cosmetic, agricultural, food, and pharmaceutical industries. These are complex mixtures of a wide range of volatile molecules, including phenol-derived aliphatic and aromatic compounds and terpenoids. Essential oils have been used medicinally since ancient times for their antibacterial, antifungal, antiviral, antiparasitic, insecticidal, sedative, antiinflammatory, and anaesthetic properties. However, essential oils come with inherent limitations; thus, nanoencapsulation is advocated as a remedy as it has the potential to enhance the stability, solubility, and effectiveness of formulations based on essential oils, all while preserving the therapeutic drug blood levels. It is not always viable to use essential oils independently in treatment due to several restrictions; however, nanodelivery technologies appear capable of overcoming these challenges. The therapeutic efficacy that is achieved can be affected by several factors, including the selection of the essential oil as well as the system of nanodelivery. Today, nanoencapsulation is capable of enabling the simultaneous delivery of multiple oils, providing synergistic effects, and facilitating the development of combinational therapies. Additionally, they may have potential applications in preserving food to prolong the shelf life of quickspoiling items and their fragrances. While there is already much research on the characterisation of EOs, this review evaluates the features of the nanoparticles employed for the delivery of essential oils and their impact on the functionality of nano-delivered essential oils and their beneficial uses.

Experimental study on the mechanism of coal spontaneous combustion inhibition by degradation of white-rot fungus

To investigate the mechanism of inhibition of spontaneous combustion of coal by degradation of white-rot fungus, the changes of macroscopic oxidizing characteristics and microstructure of the degraded coal were investigated by the programmed temperature-raising test and the in situ Fourier-transform infrared spectroscopy experiments. The difference in gas production between the degraded coal and the blank samples indicated that the degradation inhibited the oxidation process of coal, and the intensity of the inhibition effect was different at different oxidation stages. The strongest inhibition effect was found in the accelerated oxidation stage, i.e. 80–140 °C. To further analyze the micro-mechanism of the degradation of Phanerochaete chrysosporium affecting the spontaneous combustion of coal, the relative contents of active functional groups in coal samples were compared. The results showed that the degradation affected the relative contents of hydroxyl, aliphatic hydrocarbon, and oxygenated functional groups in coal. Among them, the most significant changes of –OH and –CO- were observed at 80–140 °C. Thus, it was analyzed that Phanerochaete chrysosporium could degrade the macromolecular structure of coal by generating biological enzymes to reduce the number of oxidizable functional groups such as –OH, –CH2, –CH3, –CO-, and so on, thus reducing the risk of spontaneous combustion of coal.

Phytochemical investigation of the n-hexane-extracted oil from four umbelliferous vegetables using GC/MS analysis in the context of antibacterial activity

Umbelliferous (Apiaceae) vegetables are widely consumed worldwide for their nutritive and health benefits. The main goal of the current study is to explore the compositional heterogeneity in four dried umbelliferous vegetables viz, celery, coriander, dill, and parsley targeting their volatile profile using gas chromatography-mass spectrometry (GC–MS). A total of 133 volatile metabolites were detected belonging to 12 classes. Aromatic hydrocarbons were detected as the major components of the analyzed vegetables accounting ca. 64.0, 62.4, 59.5, and 47.8% in parsley, dill, celery, and coriander, respectively. Aliphatic hydrocarbons were detected at ca. 6.39, 8.21, 6.16, and 6.79% in parsley, dill, celery, and coriander, respectively. Polyunsaturated fatty acids (PUFA) of various health benefits were detected in parsley and represented by roughanic acid and α-linolenic acid at 4.99 and 0.47%, respectively. Myristicin and frambinone were detected only in parsley at 0.45 and 0.56%. Investigation of antibacterial activity of umbelliferous vegetables n-hexane extract revealed a moderate antibacterial activity against Gram-positive and Gram-negative bacteria with higher activity for celery and dill against Staphylococcus aureus with inhibition zone 20.3 mm compared to 24.3 mm of the standard antibacterial drug.

Modification of the Dielectric and Thermal Properties of Organic Frameworks Based on Nonterminal Epoxy Liquid Crystal with Silicon Dioxide and Titanium Dioxide

A nonterminal liquid crystal epoxy monomer is used to create an epoxy–amine network with a typical diamine 4,4′diaminodiphenylmethane. The plain matrix is compared to matrices modified with inorganic fillers: TiO2 or SiO2. Conditions of the curing reaction and glass transition temperatures in the cured products are determined through differential scanning calorimetry and broadband dielectric spectroscopy. The curing process is also followed through optical and electrical observations. The dielectric response of all investigated networks reveals a segmental α-process related to structural reorientation (connected to the glass transition). In all products, a similar process associated with molecular motions of polar groups also appears. The matrix modified with TiO2 exhibits two secondary relaxation processes (β and γ). Similar processes were observed in the pure monomer. An advantage of the network with the TiO2 filler is a shorter time or lower temperature required for optimal curing conditions. The physical properties of cured matrices depend on the presence of a nematic phase in the monomer and nonterminal functional groups in the aliphatic chains. In effect, such cured matrices can have more flexibility and internal order than classical resins. Additional modifiers used in this work shift the glass transition above room temperature and influence the fragility index in both cases.

Structural investigation of interactions between halogenated flavonoids and the lipid membrane along with their role as cytotoxic agents

This study focuses on understanding the structural and molecular changes in lipid membranes under the influence of six halogenated flavonoid derivatives differing in the number and position of substitution of chlorine and bromine atoms (D1–D6). Utilizing various analytical techniques, including fluorometric methods, dynamic light scattering (DLS), attenuated Fourier transform infrared spectroscopy (ATR- FTIR), and FT-Raman spectroscopy, the research aims to elucidate the mechanisms underlying the interaction of flavonoids with cell membranes. Additionally, the study includes in silico analyses to explore the physicochemical properties of these compounds and their potential pharmaceutical applications, along with toxicity studies to assess their effects on cancer, normal, and red blood cells. Our study showed the ability of halogenated derivatives to interact mostly with the outer part of the membrane, especially in the lipid heads region however, some of them were able to penetrate deeper into the membrane and affect the fluidity of hydrocarbon chains. The potential to reduce cancer cell viability, the lack of toxicity towards erythrocytes, and the favourable physicochemical and pharmacokinetic properties suggest these halogenated flavonoids potential candidates for exploring their potential for medical use.

The Analysis of Leontopodium leontopodioides (Willd.) Beauv. Chemical Composition by GC/MS and UPLC-Q-Orbitrap MS.

Leontopodium leontopodioides (Willd.) Beauv. (L. leontopodioides.) has been used to treat lung diseases in traditional Chinese medicine (TCM). However, a systematic analysis of its chemical components has not been reported so far. In this study, UPLC-Q-Orbitrap MS and GC-MS were applied to investigate the chemical composition of the water extracts and essential oils of L. leontopodioides. UPLC-Q-Orbitrap MS adopts a heating electrospray ionization source, collecting primary and secondary mass spectrometry data in positive and negative ions, respectively, and uses Compound Discoverer 3.2 software to analyze the collected raw data. As a result, a total of 39 compounds were identified from their high-resolution mass spectra in both positive and negative ionization modes, including 13 flavonoids and their glycosides, 15 phenolic acids, 4 oligosaccharides and glycosides, 4 pentacyclic triterpenoids, and 3 other compounds. Among them, 18 chemical components have not been reported in L. leontopodioides. In the GC-MS section, two common organic solvents (n-hexane and diethyl ether) were used to extract essential oils, and the mass spectra were recorded at 70 eV (electron impact) and scanned in the range of 35∼450 m/z. Compounds were identified using NIST (version 2017), and the peak area normalization method was used to calculate their relative amounts. Finally, 17 components were identified in the volatile oil extracted with n-hexane, accounting for 80.38% of the total volatile oil, including monoterpenoids, phenylpropene, fatty acids, and aliphatic hydrocarbons. In the volatile oil extracted with diethyl ether, 16 components were identified, accounting for 73.50% of the total volatile oil, including phenylpropene, aliphatic hydrocarbons, monoterpenoids, fatty acids, and esters. This study was the first to conduct a comprehensive analysis of the chemical composition of the L. leontopodioides water extract and its essential oil, and a comprehensive chemical composition spectrum was constructed, to lay a foundation for its further pharmacodynamic material basis and quality evaluation.

Incorporating porous carbon materials into ionic liquid for high efficiency extraction of polycyclic aromatic hydrocarbons

Ionic liquid is an ideal candidate in the extraction of aromatic compounds. The design and construction of ionic liquids with high extraction efficiency and selectivity towards to the specific aromatics remain crucial question. In this paper, with the aid of orthogonal array experiment, the imidazolium-based ionic liquids with long alkyl chain on the cations were determined to possess high aromatics extraction efficiency. Furthermore, the Lewis acid anion was introduced into the ionic liquid to form 1-dodecyl-3-methylimidazolium ferric chloride ([C12mim][FeCl4]) and performed 62 % and 100 % extractant efficiency of naphthalene (NAP) and anthracene (ANT), respectively. Then the porous carbon materials (P1-1000) derived from hyper-crosslinked porous polymers (HCP) which possessed high BET surface area (1186 m2/g) was dispersed in [C12mim][FeCl4] to form porous ionic liquid. The single extraction efficiency of NAP improved from 62 % to 77 %. The great single extraction efficiency was attributed to the high porosity, additional adsorption sites provided by the Lewis acid anions and the hydrophobic long alkyl chain on the cations. After three times extraction, the concentration of NAP dropped down to 0. The porous ionic liquids also showed good recycle performance. The construction of porous ionic liquids provided an efficient approach for extraction of polycyclic aromatic hydrocarbons from aliphatic hydrocarbon.

The loss of dissolved organic matter from biological soil crust at various successional stages under rainfall of different intensities: Insights into the changes of molecular components at different rainfall stages

Biological soil crusts (BSCs) are typical covers in arid and semiarid regions. The dissolved organic matter (DOM) of BSCs can be transported to various aquatic ecosystems by rainfall-runoff processes. However, the spatiotemporal variation in quality and quantity of DOM in runoff remains unclear. Herein, four kinds of runoff plots covered by four successional stages of BSCs were set up on slopes, including bare runoff plot (BR), cyanobacteria crust covered runoff plot (CR), mixed crust covered runoff plot (MIR), and moss crust covered runoff plot (MOR). The quantity and quality of DOM in runoff during rainfall was investigated based on the stimulated rainfall experiments combined with optical spectroscopy and ultra-high resolution mass spectrometry analyses. The results showed that the DOM concentrations (i.e., 0.30 to 45.25 mg L−1) in runoff followed the pattern of MOR>MIR>CR>BR, and they were exponentially decreased with rainfall duration. The DOM loss rate of BR (8.26 to 11.64 %) was significantly greater than those of CR, MIR, and MOR (0.84 to 3.22 %). Highly unsaturated compounds (HUCs), unsaturated aliphatic compounds (UACs), saturated compounds (SCs), and peptide-like compounds (PLCs) were the dominated compounds of the water extractable DOM from the original soils. Thereinto, PLCs and UACs were more easily leached into runoff during rainfall. The relatively intensity of HUCs in runoff generally decreased with rainfall duration, while the relatively intensities of UACs, PLCs, and SCs slightly increased with rainfall duration. These findings suggested that the DOM loss rate was effectively decreased with the successional of BSCs during rainfall; meanwhile, some labile compounds (e.g., PLCs and UACs) were transported into various aquatic ecosystems by rainfall-runoff processes.

Tuning high- and low-temperature rheological properties of warm-mixing asphalt composites by functionalized waxes

Traditional asphalt road construction utilizes hot-mixing asphalt mixtures. High temperatures not only accelerate the aging of asphalt, but also produce large amounts of toxic and greenhouse gases. To alleviate these problems, wax-based warm-mixing agents are applied, and asphalt pavement construction temperatures can be efficiently lowered, resulting in lower energy and gas emissions. To systematically evaluate the effects of composition and structure of warm-mixing agents on rheological properties of asphalt at high and low temperatures, a series of functionalized waxes (i.e., oxygen-containing groups, amide groups, and long-chain aliphatic hydrocarbons) were designed in this work, followed by a melt-mixing process with asphalt. The findings demonstrated that warm-mixing agents with long-chain aliphatic hydrocarbons could significantly improve asphalt composites’ rheological properties at high temperatures, such as good viscosity-reducing effect and superior rutting resistance or permanent deformation resistance; warm-mixing agents with oxygen groups were able to improve the asphalt composites’ resistance to low-temperature cracking; amide group-containing warm-mixing agents could improve the surface roughness of asphalt composites. This work provides a practical guide for the selection of functionalized warm-mixing agents for asphalt pavement under multiple environmental factors.

Enhancing the conversion of waste motor oil into diesel-like fuels using mineral-impregnated biochar catalysts

This study shows how the presence of metal-impregnated biochar influences the kinetics of the catalytic conversion of waste motor oil (WMO) into a diesel-like fuel (DLF). First, the initial metal concentration in the wet impregnation process was optimized, showing that high metal concentrations tend to clog the biochar pores, reducing the reaction’s conversion and speed. Zinc and calcium showed higher kinetic constants at the optimized conditions than nickel, while the yield- and selectivity-to-liquid products were unaffected. Then, a reduction method was developed for impregnating metal particles of calcium oxide to enhance the metal dispersion at the biochar surface. This material showed the best performance in the reaction due to the presence of small particles instead of metal agglomerates. An increase of about 280% in the kinetic constant at 420 °C and a much lower activation energy (246 kJ mol−1) compared to the thermal cracking (308 kJ mol−1) was obtained. Finally, the DLF from the best catalytic system was analyzed. Interestingly, the fuel showed similar rheological properties to commercial diesel with a similar hydrocarbon distribution but with the presence of smaller hydrocarbon chains.

Tailoring supramolecular solvents with phosphoryl groups for highly efficient extraction of chlorophenols in natural waters

BackgroundChlorophenols are routinely determined in aquatic systems to check compliance with the restrictive international legislations set for protection of human and aquatic life. Their control requires affordable analytical methods, particularly in labs at low- and medium-income countries. Liquid chromatography-UV detection is a convenient technique for this purpose, but the availability of suitable sample processing remains pending. Organic solvents are inefficient for extracting the whole range of chlorophenols whereas solid-phase extractions are expensive and labour-intensive. So, an efficient, fast and cheap extraction of chlorophenols, amenable to any lab, would help to cope with their worldwide analytical control in natural waters. ResultsA supramolecular solvent (SUPRAS) was tailored for providing mixed interaction mechanisms aimed at the efficient extraction of chlorophenols prior to LC-UV. The SUPRAS was synthesized from the self-assembly of hexylphosphonic acid under acidic conditions and consisted of sponge-like nanostructures made up of amphiphile and water. The phosphoryl (PO) group was selected as the major driver of the extraction because of its ability to act as halogen and hydrogen bond acceptor for chlorophenols. Additional interactions were hydrogen bonds from O–H amphiphilic groups and the surrounding water, and dispersion and CH-π interactions in the hydrocarbon chains. The number of binding sites in the SUPRAS could be modulated by addition of salt. The SUPRAS formed in situ in the sample, the extraction took 5 min, the concentration factor was around 220, quantification limits (0.1–0.3 μg L−1) were below the EU standards, and the method worked for natural waters. SignificanceA fast, low-cost, and organic solvent-free sample processing only requiring conventional lab equipment (stirrers and centrifuges) provided SUPRAS extracts that could be directly analyzed by LC-UV. SUPRAS synthesis occurred spontaneously in the water sample under addition of hexylphosphonic acid and the whole process required low skills. The method meets the analytical and operational performances for the analytical control of chlorophenols in natural waters and it is within the reach of any lab.

Optimal conditions for nano-emulsified vegetable oil synthesis for the biostimulation of 1,1,2-trichloroethane and vinyl chloride contaminated groundwater in bioreactors

Contamination of groundwater with chlorinated aliphatic hydrocarbons (CAHs) has become increasingly widespread. Enhanced reductive dechlorination (ERD) by emulsified vegetable oil (EVO) is an environmentally friendly, low-carbon and sustainable technology that effectively eliminates the threat from CAHs. To improve the permeability and bioavailability of EVO in the low-permeability substratum, nano-emulsified vegetable oil (nanoEVO) can be synthesized using a modified phase inversion composition method (MPIC) by increasing the emulsification temperature that reduces the shear force required for the formation of nanodroplets and the interfacial tension between the mixed phase and water. The emulsification temperature of 60 °C, the water content of 40–70%, the droplet diameter (DD) of nanoEVO prepared by MPIC is ∼200 nm, and had good monodispersion (≤0.2). The high molecular weight and low solubility of vegetable oil, and similar size of droplet make nanoEVO remains homogeneous after storage for > one year. NanoEVO can effectively biostimulate indigenous bacteria in CAHs-contaminated groundwater to dechlorinate 1,1,2-trichloroethane (1,1,2-TCA) to ethene via vinyl chloride (VC). The maximum dihaloelimination rate of 1,1,2-TCA was ∼66.06 μM·Cl−·day−1 and the maximum hydrogenolysis rate of VC was ∼35.67 μM·Cl−·day−1. NanoEVO effectively increased the relative abundance of Dehalococcoides from <0.10 to 9.61%. The abundances of Dhc 16S rRNA gene and dehalogenase gene vcrA increased by 102 and 103, respectively. Biostimulation shaped the structure of microbial communities and promoted hydrolytic acidification and anaerobic fermentation. Moreover, the syntrophic VFA-oxidizing bacteria participated in secondary fermentation and were closely correlated with H2 consumption metabolism. By providing carbon sources and maintaining an anaerobic environment with stable pH and ORP, nanoEVO biostimulated the hydrolytic acidification led by fermentative bacteria, secondary fermentation with syntrophic VFA-oxidizing bacteria and reductive dechlorination carried out by dechlorinator, thus greatly increasing the CAH-dechlorinating ability of indigenous microbial communities.

Investigating the Potential of Phenolic Compounds and Carbohydrates as Acceptor Substrates for Levansucrase-Catalyzed Transfructosylation Reaction.

This study characterizes the acceptor specificity of levansucrases (LSs) from Gluconobacter oxydans (LS1), Vibrio natriegens (LS2), Novosphingobium aromaticivorans (LS3), and Paraburkholderia graminis (LS4) using sucrose as fructosyl donor and selected phenolic compounds and carbohydrates as acceptors. Overall, V. natriegens LS2 proved to be the best biocatalyst for the transfructosylation of phenolic compounds. More than one fructosyl unit could be attached to fructosylated phenolic compounds. The transfructosylation of epicatechin by P. graminis LS4 resulted in the most diversified products, with up to five fructosyl units transferred. In addition to the LS source, the acceptor specificity of LS towards phenolic compounds and their transfructosylation products were found to greatly depend on their chemical structure: the number of phenolic rings, the reactivity of hydroxyl groups and the presence of aliphatic chains or methoxy groups. Similarly, for carbohydrates, the transfructosylation yield was dependent on both the LS source and the acceptor type. The highest yield of fructosylated-trisaccharides was Erlose from the transfructosylation of maltose catalyzed by LS2, with production reaching 200 g/L. LS2 was more selective towards the transfructosylation of phenolic compounds and carbohydrates, while reactions catalyzed by LS1, LS3 and LS4 also produced fructooligosaccharides. This study shows the high potential for the application of LSs in the glycosylation of phenolic compounds and carbohydrates.

Electrocatalytic Formal C(sp2)–H Alkylations via Nickel‐Catalyzed Cross‐Electrophile Coupling with Versatile Arylsulfonium Salts

Producing sp3‐hybridized carbon‐enriched molecules is of particular interest due to their high success rate in clinical trials. The installation of aliphatic chains onto aromatic scaffolds was accomplished by nickel‐catalyzed C(sp2)–C(sp3) cross‐electrophile coupling with arylsulfonium salts. Thus, simple non‐prefunctionalized arenes could be alkylated through the formation of aryldibenzothiophenium salts. The reaction employs an electrochemical approach to avoid potentially hazardous chemical redox agents, and importantly, the one‐pot alkylation proved also viable, highlighting the robustness of our approach.

Electrocatalytic Formal C(sp2)-H Alkylations via Nickel-Catalyzed Cross-Electrophile Coupling with Versatile Arylsulfonium Salts.

Producing sp3-hybridized carbon-enriched molecules is of particular interest due to their high success rate in clinical trials. The installation of aliphatic chains onto aromatic scaffolds was accomplished by nickel-catalyzed C(sp2)-C(sp3) cross-electrophile coupling with arylsulfonium salts. Thus, simple non-prefunctionalized arenes could be alkylated through the formation of aryldibenzothiophenium salts. The reaction employs an electrochemical approach to avoid potentially hazardous chemical redox agents, and importantly, the one-pot alkylation proved also viable, highlighting the robustness of our approach.

Self-blowing, hybrid non-isocyanate polyurethane foams produced at room temperature

Self-blowing polyurethane foams are essential for several everyday applications, yet their traditional production involves fossil-derived products and hazardous isocyanate compounds. Thus, research into isocyanate-free polyurethane foams is receiving considerable attention. However, current approaches often rely on external blowing agents, and/or high temperatures with long polymerization times. This research presents a rapid, self-blowing, partially bio-based non-isocyanate polyurethane (NIPU) foams at room temperature, specifically poly(hydroxy-thio-urethane), with both rigid and flexible configurations. The method involves the partial conversion of an epoxy resin to an oligomer mixture composed of 85% bio-cyclic carbonate and 15% of non-converted epoxide. This oligomer undergoes a fast process, through reactions between the epoxy groups and the reactive components, that is then followed by simultaneous aminolysis and decarboxylation reactions, arising from the interaction of an amine and cyclic carbonate. An in-situ blowing agent (CO2) is generated from the interaction between thiols and cyclic carbonate. The glass transition temperature is modulated by the thiol/amine content in rigid foams and by the addition of aliphatic long chains in flexible foams. With almost 30% renewable carbon content, these foams provide a sustainable alternative to traditional isocyanate-based pathways. The resulting porous materials possessed densities between 0.158 and 0.201 g/cm3. Finally, the foams can be transformed into films, enhancing recyclability and sustainability at the end of their lifecycle. Thus, this development has the potential to facilitate the production of eco-friendly, recyclable polyurethane foams.

Photopolymerizable semi-crystalline polymers for thermally reversible, 3D printable cast molds

ObjectivesThis study demonstrates the use of photopolymerization to create semi-crystalline linear polymers suitable for thermally reversible materials in dental cast moldings produced from 3D printing. MethodsAn aromatic diallyl, aliphatic dithiol chain extender, and monofunctional thiol were used in a photoinitiated system. The photopolymerization and crystallization kinetics as a function of chemistry and temperature were investigated using spectroscopy and calorimetry. These insights were used to realize vat photopolymerization-based 3D printing of functional objects that could be remotely melted and thereby removed using induction heating. ResultsThe addition of monothiol was shown to decrease the polymer molecular weight which correspondingly increased the crystallization rate. Photopolymerization kinetics are independent of temperature while crystallization was slowed as the temperature approaches the melting point of the materials. Through inclusion of chromium oxide, semicrystalline materials could be melted through induction heating. These materials were implemented in vat photopolymerization 3D printing to realize high-resolution objects that could be used as releasable dental molds following printing and induction heating. SignificanceThis work demonstrates a proof-of-concept methodology to realize directly printable, thermally reversible semicrystalline materials for potential use as dental molding materials.